Simple Installation Methods for a New Shower Unit

Blog Article

Prep work

Firstly, you need to decide on the type of shower that you wish to install. It is essential to establish whether the selected shower is capable of handling specific systems and can regulate a secure degree of water with the central heating boiler. Many shower systems nowadays are created to be versatile to different water pressures (such as saved hot water and also cold keys).
It is likewise important to take into account the water stress and the preparation of the piping and also water drainage for the shower

Various Sorts Of Shower Units

Push-on Mixer: The hose pipe as well as spray parts of the push-on mixer shower device can be attached to the bathroom tap according to your demand, and also the water temperature level can be adjusted through the taps. Push-on mixers are cheap and very basic to mount. Nevertheless, although the pipe link is straightforward, it is conveniently dislodged. Furthermore, it is bothersome to readjust the temperature.

Bath/Shower Mixer: The hose pipe as well as spray of this kind of shower are integrated with a bath mixer tap, and the temperature level can be readjusted with the bathroom taps. It is a very low-cost alternative as well as no extra plumbing is entailed. Nevertheless, the bath/shower mixers additionally struggle with inconvenient temperature level control options.

Guidebook Mixer: The hose pipe and also spray of a hands-on mixer shower device belong of the wall system and also the hot and cold water products are connected to a solitary shutoff The temperature level and also pressure of the water are managed through either one or a range of knobs (in much more expensive showers). Although temperature control is a lot easier in hands-on mixer types, they are a lot more costly than the previously stated mixers. They also call for extra plumbing of hot and cold supply of water pipes.

Thermostatic Mixer: The pipe as well as spray of this shower type are a part of the wall system and also the hot and cold water products are linked to a solitary shutoff here as well. It is full with a built-in stabiliser to self-adjust the water temperature level and also to prevent it from coming to be as well warm. One of the largest advantages of a thermostatic mixer shower kind consists of convenient temperature level control. Nonetheless, it is one of the most costly of the various mixer alternatives.

Power Shower: A power shower is a solitary unit containing a powerful electric pump that can altering both the water pressure and also temperature level. This sort of shower can be fitted if there is water supply from a cold water tank as well as a hot water cylinder. A power shower makes the modification of both stress and temperature level simple. On the other hand, it is unsuitable for water heated directly by the shower or where the water is supplied by a mix central heating boiler under mains pressure.

Electric Shower: An electrical shower is plumbed into a keys cold water supply as well as it heats up the water electrically. It is necessary to note that for this shower type to be set up, the mains pressure requires to be at the very least 0.7 kg/sq centimeters (10lb/sq in). The device allows the temperature and pressure to be adjusted using a knob. Versions with temperature level stabilisers are better as they stay unaffected by other faucets somewhere else being used within the home. A significant disadvantage of electric showers is that the control handle only enables the option of heats at much less pressure, or lower temperature levels at a higher stress. This is bothersome in the winter season when the spray is typically weak and also the keys water is colder. However, this issue is taken on in some models which are readily available with a winter/summer setting.

Approach

Relying on the kind of shower you desire to mount, the shower head have to either be suited order to prevent its contact with the water in the bathroom below or the base tray, or it should have a check valve.
Prior to starting, it is recommended to mark the positions of the shower head and also control, and also to prepare the pipe-work included. Additionally, the drain system to remove the drainage will certainly require to be prepared. Both positions of the wire course and also the shower switch will additionally need to be considered if an immediate or electrical shower system is being installed.
Make use of the guideline guide given with the shower system to fit the shower control.Before fitting the pipelines that will supply the water to the shower system, it is very important to remove the water. In order to protect the pipelines, they must be offered a water-proof covering as well as also fitted with separating shutoffs. The pipelines can after that be hidden right into the wall surface and plastered over to neaten the overall look.
Fit the base tray, shower head, and also fittings.
Attach the primary shower control to the pipes that will be supplying the water (This might require a women screw string adapter).
Reconnect the water supply as well as test the pipelines for any type of leaks, as some might require tightening.
If you are mounting an electrical shower, bear in mind to turn off the electrical energy supply prior to making any kind of electric links. As soon as these connections have been made (there should be assistance within the instruction manual), the power supply can be switched back on.

Readjusting Water Pressure to Suit Your Shower

The cold water storage tank can be lifted to a greater height (sometimes just 150mm (6inches)) by fitting a solid wooden support under it - potentially made up of struts as well as blockboards. If you pick this alternative, the primary as well as circulation pipes will likewise need to be increased to satisfy the brand-new elevation of the reservoir.
Additionally, a booster pump (a solitary pump or a dual/twin pump) can be fitted. Whichever kind is selected, it has to be connected into the power supply in order to operate.

Piping and Drainage

It is best to utilize 15mm diameter supply pipes, and make the go to the shower as short and also straight as feasible so as to maintain maximum pressure and also minimise heat loss. Furthermore, by minimising the use of elbows for pipeline corners, you can lower the resistance in the circulation of the water system. You can achieve this by flexing the pipelines instead.

Most Typical Mistakes

Going against or disregarding neighborhood code restrictions.

Making use of pipes that are also small.

Connecting copper to galvanized without making use of a brass or dielectric fitting between both.

Not making use of tape or pipe compound at threaded joints.

Uneven your components when installing them.

Not installing an air space loading for components.

Reducing supply stub outs also short to set up the shutoff valves onto after the completed wall surface remains in area.

Not effectively aligning tubes right into installations or quit valves. (Forcing the nut onto the compression ring at an angle when the tubing goes to an angle will certainly cause a leak.).

When turning the water back on in your home, constantly run the outside hose pipe shutoff or flush your commodes to bleed dust as well as air from the lines. This debris can trigger troubles in your sink faucets as well as various other plumbing trim.

How Do You Install a Shower? Follow This Guide

Installing a Shower at a Glance

Tools & Materials: Level, electric drill, caulk, hole saw, cedar shims, shower unit

Step 1: Drill pilot holes

Step 2: Prep fixture holes

Step 3: Move unit into place

Step 4: Caulk corners and base

Step 5: Attach door

Step 6: Install shower pan

Whenever plumbing is involved in a DIY project, people worry about what might go wrong. The truth is that installing a shower isn’t that complicated, and you can save a lot of money by doing it yourself. You shouldn’t need to make any alterations to your plumbing to complete the job, and most of the tools you need will be provided in your new shower kit.

Can I Install a Shower Myself?

Even if you’ve never installed a shower before, you’ll find this to be a project that is perfectly suited for DIYers with a moderate level of experience. Whether you're doing a bathtub conversion or installing a new stall, most of what you need comes in shower kits that you can purchase from a hardware store. The first thing you need to do is determine what type of shower stall you want.

Single-panel stalls are the easiest to install because they come preassembled. All you need to do is put them in place. Multi-panel showers require a few additional steps, but you’ve got more control over the appearance of your unit. Multi-panel units are also much easier to handle if you’re going to do the installation without any help.

Be sure to take all appropriate safety precautions, such as wearing eye protection and gloves. When you’re removing or installing a shower unit, you might kick up debris that could hurt your eyes. You’ll also need to work with equipment that will get extremely hot, so be sure to have safety gloves handy.

Tools and Materials

2- to 4-foot level

Electric drill with a 1/8-inch drill bit

Caulk

2-inch hole saw

Cedar shims

The unit itself

Before You Begin: Prep the Space

It’s highly important to measure your space accurately before putting the stall in. Measuring from the floor upward and from each corner outward will ensure you’ve got the right measurements. What you’re looking for is where the plumbing apparatuses are going to come through the stall. Transfer these measurements over to the back of your unit by drawing the locations of these holes using a pencil or marker.

Pull out your old shower and make sure to scrape off all the old caulking. Be thorough because you want to work with smooth surfaces for the best installation. Once you’ve pulled out your existing shower, you need to make sure that the floor is clean and dry. The best way to clean debris is with a shop vacuum, as it’ll soak up water and dirt together.

If you’re experiencing any plumbing issues, such as low water pressure, this is a perfect opportunity to solve them. Make sure that the pipes themselves are not in need of patching and clean your showerhead. When you turn the water back on after your project, check the pipes for signs of wear or disrepair. Anything beyond minor repairs should be handled by a plumber, and this is the best time to bring in a professional.

If the floor has any moisture at all, don’t proceed until it’s completely dry. The last thing you need is for the floor to rot or invite mold and mildew into your base. Once everything is dry, apply waterproof wallboard to the walls. This can be attached with screws or nails, then sealed with caulk so that water doesn’t seep into any crevices.
https://www.homeserve.com/en-us/blog/how-to/install-shower/

We were made aware of that article on How to Install a Direct-to-Stud Shower Enclosure from someone on our other web blog. Liked our blog posting? Please share it. Let others locate it. I praise you for your time. Please visit our blog back soon.

Book A Service Call

Report this page

SIMPLE INSTALLATION METHODS FOR A NEW SHOWER UNIT

Simple Installation Methods for a New Shower Unit